 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 Future Technology Devices International Ltd FT2232H Dual High Speed USB to Multipurpose UART/FIFO IC The FT2232H is FTDI's 5th generation of USB devices. The FT2232H is a USB * 2.0 High Speed (480Mb/s) to UART/FIFO IC. It has the capability of * being configured in a variety of industry standard serial or parallel * interfaces. The FT2232H has the following advanced features: * * * * Single chip USB to dual serial / parallel ports with a variety of configurations. Entire USB protocol handled on the chip. No USB specific firmware programming required. USB 2.0 High Speed (480Mbits/Second) and Full Speed (12Mbits/Second) compatible. Dual Multi-Protocol Synchronous Serial Engine (MPSSE) to simplify synchronous serial protocol 2 (USB to JTAG, I C, SPI or bit-bang) design. Dual independent UART or FIFO ports configurable using MPSSEs. Independent Baud rate generators. RS232/RS422/RS485 UART Transfer Data Rate up to 12Mbaud. (RS232 Data Rate limited by external level shifter). USB to parallel FIFO transfer data rate up to 8 Mbyte/Sec. Single channel synchronous FIFO mode for transfers > 25 Mbytes/Sec CPU-style FIFO interface mode simplifies CPU interface design. MCU host bus emulation mode configuration option. Fast Opto-Isolated serial interface option. FTDI's royalty-free Virtual Com Port (VCP) and Direct (D2XX) drivers eliminate the requirement for USB driver development in most cases. Adjustable receive buffer timeout. * * Option for transmit and receive LED drive signals on each channel. Enhanced bit-bang Mode interface option with RD# and WR# strobes FT245B-style FIFO interface option with bidirectional data bus and simple 4 wire handshake interface. Highly integrated design includes +1.8V LDO regulator for VCORE, integrated POR function and on chip clock multiplier PLL (12MHz - 480MHz). Asynchronous serial UART interface option with full hardware handshaking and modem interface signals. Fully assisted hardware or X-On / X-Off software handshaking. UART Interface supports 7/8 bit data, 1/2 stop bits, and Odd/Even/Mark/Space/No Parity. Auto-transmit enable control for RS485 serial applications using TXDEN pin. Operational configuration mode and USB Description strings configurable in external EEPROM over the USB interface. Configurable I/O drive strength (4, 8, 12 or 16mA) and slew rate. Low operating and USB suspend current. Supports bus powered, self powered and highpower bus powered USB configurations. UHCI/OHCI/EHCI host controller compatible. USB Bulk data transfer mode (512 byte packets in High Speed mode). +1.8V (chip core) and +3.3V I/O interfacing (+5V Tolerant). Extended -40C to 85C industrial operating temperature range. Compact 64-LD Lead Free LQFP or QFN package +3.3V single supply operating voltage range. * * * * * * * * * * * * * * * * * * * * * * * Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640 Copyright (c) 2009 Future Technology Devices International Limited 1 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 1 * * * * * * * * * Typical Applications Single chip USB to dual channel UART (RS232, RS422 or RS485). Single chip USB to dual channel FIFO. Single chip USB to dual channel JTAG. Single chip USB to dual channel SPI. Single chip USB to dual channel I2C. Single chip USB to dual channel Bit-Bang. Single chip USB to dual combination of any of above interfaces. Single chip USB to Fast Serial Optic Interface. Single chip USB to CPU target interface (as memory), double and independent. * * * * * * * * * * Single chip USB to Host Bus Emulation (as CPU). PDA to USB data transfer USB Smart Card Readers USB Instrumentation USB Industrial Control USB MP3 Player Interface USB FLASH Card Reader / Writers Set Top Box PC - USB interface USB Digital Camera Interface USB Bar Code Readers 1.1 Driver Support The FT2232H requires USB drivers (listed below) , available free from http://www.ftdichip.com, which are used to make the FT2232H appear as a virtual COM port (VCP). This allows the user to communicate with the USB interface via a standard PC serial emulation port (for example TTY). Another FTDI USB driver, the D2XX driver, can also be used with application software to directly access the FT2232H through a DLL. Royalty free VIRTUAL COM PORT (VCP) DRIVERS for... * * * * * * * Windows 2000, Server 2003, Server 2008 Windows XP and XP 64-bit Windows Vista and Vista 64-bit Windows XP Embedded Windows CE 4.2, 5.0, 5.2 and 6.0 Mac OS-X Linux (2.6.9 or later) Royalty free D2XX Direct Drivers (USB Drivers + DLL S/W Interface) * * * * * * Windows 2000, Server 2003, Server 2008 Windows XP and XP 64-bit Windows Vista and Vista 64-bit Windows XP Embedded Windows CE 4.2, 5.0, 5.2 and 6.0 Linux (2.4 or later) and Linux x86_64 For driver installation, please refer to the application note: * AN_106, "Advanced Driver Options". The following additional installation guides and technical notes are also available: * * * * * * * * AN_103, "FTDI Drivers Installation Guide for VISTA". AN_104, "FTDI Drivers Installation Guide for WindowsXP". AN_108, "Command Processor for MPSSE and MCU Host Bus Emulation Modes ". AN_109, "Programming Guide for High Speed FTCI2C DLL ". AN_110, "Programming Guide for High Speed FTCJTAG DLL ". AN_111, "Programming Guide for High Speed FTCSPI DLL ". AN_113, "Interfacing FT2232H Hi-Speed Devices To I2C Bus". TN_104, "Guide to Debugging Customers Failed Driver Installation" Copyright (c) 2009 Future Technology Devices International Limited 2 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 1.2 Part Numbers Package Part Number FT2232HL-xxxx FT2232HQ-xxxx Note: Packing codes for xxxx is: 64 Pin LQFP 64 Pin QFN - Reel: Taped and Reel (LQFP =1000 pcs per reel, QFN =4000 pcs per reel) -Tray: Tray packing, (LQFP =160 pcs per tray, QFN =260 pcs per tray) Please refer to section 8 for all package mechanical parameters. 1.3 USB Compliant At the time of writing this datasheet, the FT2232H (Rev B) was still to complete USB compliancy testing. Copyright (c) 2009 Future Technology Devices International Limited 3 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 2 FT2232H Block Diagram VCC 3V3 IN 120 MHz 120 MHz Baud Rate Generator Dual Port TX Buffer 4K Bytes Dual Port RX Buffer 4K Bytes ADBUS0 ADBUS1 ADBUS2 ADBUS3 ADBUS4 ADBUS5 ADBUS6 ADBUS7 ACBUS0 ACBUS1 ACBUS2 ACBUS3 ACBUS4 ACBUS5 ACBUS6 ACBUS7 V1.8OUT 1.8 Volt LDO Regulator EECS EESK EEDATA EEPROM Interface MPSSE/ Multipurpose UART/FIFO Controller OSCI OSCO USBDP UTMI PHY USBDM USB Protocol Engine And FIFO Control PWREN# SUSPEND# RREF 120 MHz 120 MHz Baud Rate Generator Dual Port TX Buffer 4K Bytes Dual Port RX Buffer 4K Bytes TEST BDBUS0 BDBUS1 BDBUS2 BDBUS3 BDBUS4 BDBUS5 BDBUS6 BDBUS7 BCBUS0 BCBUS1 BCBUS2 BCBUS3 BCBUS4 BCBUS5 BCBUS6 PWRSAV# / BCBUS7 RESET# RESET Generator MPSSE/ Multipurpose UART/FIFO Controller Figure 2.1 FT2232H Block Diagram For a description of each function please refer to Section 4. Copyright (c) 2009 Future Technology Devices International Limited 4 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 Table of Contents 1 1.1 1.2 Typical Applications ...................................................................... 2 Driver Support .................................................................................... 2 Part Numbers...................................................................................... 3 Note: Packing codes for xxxx is: ................................................................. 3 1.3 USB Compliant .................................................................................... 3 2 3 3.1 3.2 3.3 3.4 FT2232H Block Diagram ............................................................... 4 Device Pin Out and Signal Description .......................................... 7 64-Pin LQFP and 64-Pin QFN Package Schematic Symbol ................... 7 FT2232H Pin Descriptions ................................................................... 8 Common Pins ...................................................................................... 9 Configured Pins ................................................................................ 11 FT2232H pins used in an RS232 interface ..................................................................... 11 FT2232H pins used in an FT245 Style Synchronous FIFO Interface ................................... 12 FT2232H pins used in an FT245 Style Asynchronous FIFO Interface ................................. 13 FT2232H pins used in a Synchronous or Asynchronous Bit-Bang Interface ........................ 14 FT2232H pins used in an MPSSE .................................................................................. 15 FT2232H Pins used as a Fast Serial Interface ................................................................ 16 FT2232H Pins Configured as a CPU-style FIFO Interface ................................................. 17 FT2232H Pins Configured as a Host Bus Emulation Interface ........................................... 18 3.4.1 3.4.2 3.4.3 3.4.4 3.4.5 3.4.6 3.4.7 3.4.8 4 4.1 4.2 4.3 Function Description................................................................... 19 Key Features ..................................................................................... 19 Functional Block Descriptions ........................................................... 19 Dual Port FT232 UART Interface Mode Description ........................... 21 Dual Port RS232 Configuration .................................................................................... 21 Dual Port RS422 Configuration .................................................................................... 22 Dual Port RS485 Configuration .................................................................................... 23 4.3.1 4.3.2 4.3.3 4.4 4.4.1 4.4.2 FT245 Synchronous FIFO Interface Mode Description ...................... 24 FT245 Synchronous FIFO Read Operation ..................................................................... 25 FT245 Synchronous FIFO Write Operation ..................................................................... 25 4.5 4.6 4.7 4.7.1 4.7.2 FT245 Asynchronous FIFO Interface Mode Description..................... 26 MPSSE Interface Mode Description. .................................................. 28 MCU Host Bus Emulation Mode ......................................................... 29 MCU Host Bus Emulation Mode Signal Timing - Write Cycle............................................. 30 MCU Host Bus Emulation Mode Signal Timing - Read Cycle ............................................. 31 4.8 4.8.1 4.8.2 Fast Opto-Isolated Serial Interface Mode Description ...................... 32 Outgoing Fast Serial Data ........................................................................................... 33 Incoming Fast Serial Data ........................................................................................... 33 Copyright (c) 2009 Future Technology Devices International Limited 5 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 4.8.3 Fast Opto-Isolated Serial Data Interface Example .......................................................... 34 4.9 CPU-style FIFO Interface Mode Description ...................................... 35 4.10 Synchronous and Asynchronous Bit-Bang Interface Mode Description ................................................................................................ 37 4.11 4.12 4.12.1 RS232 UART Mode LED Interface Description ................................ 39 FT2232H Mode Selection ................................................................ 40 Do I need an EEPROM? ........................................................................................... 40 5 5.1 5.2 Devices Characteristics and Ratings ........................................... 41 Absolute Maximum Ratings............................................................... 41 DC Characteristics............................................................................. 42 6 6.1 6.2 6.3 FT2232H Configurations ............................................................. 45 USB Bus Powered Configuration ....................................................... 45 USB Self Powered Configuration ....................................................... 47 Oscillator Configuration .................................................................... 49 7 8 8.1 8.2 8.3 EEPROM Configuration................................................................ 50 Package Parameters ................................................................... 51 FT2232HQ, QFN-64 Package Dimensions .......................................... 52 FT2232HL, LQFP-64 Package Dimensions ......................................... 53 Solder Reflow Profile ........................................................................ 55 9 Contact Information ................................................................... 57 Appendix A - List of Figures and Tables .................................................... 58 List of Tables ............................................................................................. 58 Appendix B - Revision History ................................................................... 60 Copyright (c) 2009 Future Technology Devices International Limited 6 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 3 Device Pin Out and Signal Description The 64-pin LQFP and 64-pin QFN have the same pin numbering for specific functions. This pin numbering is illustrated in the schematic symbol shown in Figure 3.1. 3.1 64-Pin LQFP and 64-Pin QFN Package Schematic Symbol 50 49 VREGIN VREGOUT ADBUS0 ADBUS1 ADBUS2 ADBUS3 ADBUS4 ADBUS5 ADBUS6 ADBUS7 ACBUS0 ACBUS1 ACBUS2 ACBUS3 ACBUS4 ACBUS5 ACBUS6 ACBUS7 BDBUS0 BDBUS1 BDBUS2 BDBUS3 BDBUS4 BDBUS5 BDBUS6 BDBUS7 16 17 18 19 21 22 23 24 26 27 28 29 30 32 33 34 38 39 40 41 43 44 45 46 48 52 53 54 55 57 58 59 60 36 7 8 6 14 DM DP REF RESET# FT2232HL 63 62 61 2 EECS EECLK EEDATA OSCI 3 13 BCBUS0 BCBUS1 BCBUS2 BCBUS3 BCBUS4 BCBUS5 BCBUS6 BCBUS7 PWREN# SUSPEND# OSCO TEST Figure 3.1 FT2232H Schematic Symbol Copyright (c) 2009 Future Technology Devices International Limited 7 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 3.2 FT2232H Pin Descriptions This section describes the operation of the FT2232H pins. Both the LQFP and the QFN packages have the same function on each pin. The function of many pins is determined by the configuration of the FT2232H. The following table details the function of each pin dependent on the configuration of the interface. Each of the functions are described in the following table (Note: The convention used throughout this document for active low signals is the signal name followed by a #). Pins marked ** default to tri-stated inputs with an internal 75K (approx) pull up resistor to VCCIO. FT2232H Pin Pin # 16 17 18 19 21 22 23 24 26 27 28 29 30 32 33 34 38 39 40 41 43 44 45 46 48 52 53 54 55 57 58 59 60 36 63 62 61 Pin Name ADBUS0 ADBUS1 ADBUS2 ADBUS3 ADBUS4 ADBUS5 ADBUS6 ADBUS7 ACBUS0 ACBUS1 ACBUS2 ACBUS3 ACBUS4 ACBUS5 ACBUS6 ACBUS7 BDBUS0 BDBUS1 BDBUS2 BDBUS3 BDBUS4 BDBUS5 BDBUS6 BDBUS7 BCBUS0 BCBUS1 BCBUS2 BCBUS3 BCBUS4 BCBUS5 BCBUS6 BCBUS7 PWREN# SUSPEND# Pin functions (depends on configuration) ASYNC Serial (RS232) TXD RXD RTS# CTS# DTR# DSR# DCD# RI# TXDEN ** ** RXLED# TXLED# ** ** ** TXD RXD RTS# CTS# DTR# DSR# DCD# RI# TXDEN ** ** RXLED# TXLED# ** ** PWRSAV# PWREN# SUSPEND# 245 FIFO SYNC D0 D1 D2 D3 D4 D5 D6 D7 RXF# TXE# RD# WR# SIWUA CLKOUT OE# ** 245 FIFO D0 D1 D2 D3 D4 D5 D6 D7 RXF# TXE# RD# WR# SIWUA ** ** ** D0 D1 D2 D3 D4 D5 D6 D7 RXF# TXE# RD# WR# SIWUB ** ** ASYNC Bit-bang D0 D1 D2 D3 D4 D5 D6 D7 ** WRSTB# RDSTB# ** SIWUA ** ** ** D0 D1 D2 D3 D4 D5 D6 D7 ** WRSTB# RDSTB# ** SIWUB ** ** PWRSAV# SYNC Bitbang Channel A D0 D1 D2 D3 D4 D5 D6 D7 ** WRSTB# RDSTB# ** SIWUA ** ** ** Channel B D0 D1 D2 D3 D4 D5 D6 D7 ** WRSTB# RDSTB# ** SIWUB ** ** PWRSAV# MPSSE TCK/SK TDI/DO TDO/DI TMS/CS GPIOL0 GPIOL1 GPIOL2 GPIOL3 GPIOH0 GPIOH1 GPIOH2 GPIOH3 GPIOH4 GPIOH5 GPIOH6 GPIOH7 TCK/SK TDI/DO TDO/DI TMS/CS GPIOL0 GPIOL1 GPIOL2 GPIOL3 GPIOH0 GPIOH1 GPIOH2 GPIOH3 GPIOH4 GPIOH5 GPIOH6 GPIOH7 PWREN# SUSPEND# Fast Serial interface CPU Style FIFO D0 Host Bus Emulation AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 A8 A9 A10 A11 A12 A13 A14 A15 CS# ALE RD# WR# IORDY CLKOUT I/O0 I/O1 ** ** ** ** ** ** ** PWRSAV# USES CHANNEL B D1 D2 D3 D4 D5 D6 D7 CS# A0 RD# WR# SIWUA ** ** ** FSDI FSCLK FSDO FSCTS D0 D1 D2 D3 D4 D5 D6 D7 CS# A0 RD# WR# SIWUB SIWUB ** ** PWRSAV# PWRSAV# PWRSAV# PWRSAV# PWREN# SUSPEND# PWREN# SUSPEND# PWREN# SUSPEND# PWREN# SUSPEND# PWREN# SUSPEND# PWREN# SUSPEND# PWREN# SUSPEND# Configuration memory interface EECS EECLK EEDATA Copyright (c) 2009 Future Technology Devices International Limited 8 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 3.3 Common Pins The operation of the following FT2232H pins are the same regardless of the configured mode:Pin No. Name Type POWER Input POWER Input POWER Input POWER Input POWER Input POWER Output POWER Input POWER Input Description 12,37,64 VCORE +1.8V input. Core supply voltage input. 20,31,42,56 VCCIO +3.3V input. I/O interface power supply input. Failure to connect all VCCIO pins will result in failure of the device. +3.3V input. Internal PHY PLL power supply input. It is recommended that this supply is filtered using an LC filter. +3.3V Input. Internal USB PHY power supply input. Note that this cannot be connected directly to the USB supply. A +3.3V regulator must be used. It is recommended that this supply is filtered using an LC filter. +3.3V Input. Integrated 1.8V voltage regulator input. 9 VPLL 4 VPHY 50 VREGIN 49 VREGOUT +1.8V Output. Integrated voltage regulator output. Connect to VCORE with 3.3uF filter capacitor. 10 1,5,11,15, 25,35,47,51 AGND 0V Analog ground. GND 0V Ground input. Table 3.1 Power and Ground Copyright (c) 2009 Future Technology Devices International Limited 9 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 Pin No. Name Type INPUT OUTPUT INPUT INPUT INPUT INPUT INPUT Description 2 3 6 7 8 13 14 OSCI OSCO REF DM DP TEST RESET# Oscillator input. Oscillator output. Current reference - connect via a 12K USB Data Signal Minus. USB Data Signal Plus. IC test pin - for normal operation should be connected to GND. Reset input (active low). Active low power-enable output. PWREN# = 0: Normal operation. resistor @ 1% to GND. 60 PWREN# OUTPUT PWREN# =1 : USB SUSPEND mode or device has not been configured. This can be used by external circuitry to power down logic when device is in USB suspend or has not been configured. 36 SUSPEND# OUTPUT Active low when USB is in suspend mode. USB Power Save input. This is an EEPROM configurable option used when the FT2232H is used in a self powered mode and is used to prevent forcing current down the USB lines when the host or hub is powered off. PWRSAV# = 1 : Normal Operation 59 PWRSAV# INPUT PWRSAV# = 0 : FT2232H forced into SUSPEND mode. PWRSAV# can be connected to GND (via a 10K resistor) and another resistor (e.g. 4K7) connected to the VBUS of the USB connector. When this input goes high, then it indicates to the FT2232H that it is connected to a host PC. When the host or hub is powered down then the FT2232H is held in SUSPEND mode. Table 3.2 Common Function pins Pin No. Name Type Description 63 62 EECS EECLK EEDATA I/O OUTPUT I/O EEPROM - Chip Select. Tri-State during device reset. Clock signal to EEPROM. Tri-State during device reset. When not in reset, this outputs the EEPROM clock. EEPROM - Data I/O Connect directly to Data-In of the EEPROM and to Data-Out of the EEPROM via a 2.2K resistor. Also, pull Data-Out of the EEPROM to VCC via a 10K resistor for correct operation. Tri-State during device reset. 61 Table 3.3 EEPROM Interface Group Copyright (c) 2009 Future Technology Devices International Limited 10 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 3.4 Configured Pins The following sections describe the function of the configurable pins referred to in the table given in Section 3.2 which is determined by how the FT2232H is configured. 3.4.1 FT2232H pins used in an RS232 interface The FT2232H channel A or channel B can be configured as an RS232 interface. When configured in this mode, the pins used and the descriptions of the signals are shown in Table 3.4. Channel A Pin No. Channel B Pin No. Name Type RS232 Configuration Description 16 17 18 19 21 22 23 38 39 40 41 43 44 45 TXD RXD RTS# CTS# DTR# DSR# DCD# OUTPUT INPUT OUTPUT INPUT OUTPUT INPUT INPUT TXD = transmitter output RXD = receiver input RTS# = Ready To send handshake output CTS# = Clear To Send handshake input DTR# = Data Transmit Ready modem signaling line DSR# = Data Set Ready modem signaling line DCD# = Data Carrier Detect modem signaling line RI# = Ring Indicator Control Input. When the Remote Wake up option is enabled in the EEPROM, taking RI# low can be used to resume the PC USB Host controller from suspend. TXDEN = (TTL level). For use with RS485 level converters. RXLED = Receive signaling output. Pulses low when receiving data (RXD) via USB. This should be connected to an LED. TXLED = Transmit signaling output. Pulses low when transmitting data (TXD) via USB. This should be connected to an LED. 24 46 RI# INPUT 26 29 48 54 TXDEN RXLED OUTPUT OUTPUT 30 55 TXLED OUTPUT Table 3.4 Channel A and Channel B RS232 Configured Pin Descriptions Copyright (c) 2009 Future Technology Devices International Limited 11 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 3.4.2 FT2232H pins used in an FT245 Style Synchronous FIFO Interface The FT2232H only channel A can be configured as a FT245 style synchronous FIFO interface. When configured in this mode, the pins used and the descriptions of the signals are shown in Table 3.5. To enter this mode the external EEPROM must be set to make port A 245 mode. A software command (Set Bit Mode option) is then sent by the application to the FTDI driver to tell the chip to enter single channel synchronous FIFO mode. In this mode the `B' channel is not available as all resources have been switched onto channel A. In this mode, data is written or read on the rising edge of the CLKOUT. Channel A Pin No. Name Type FT245 Configuration Description 24,23,22,21, 19,18,17,16 ADBUS[7:0] I/O D7 to D0 bidirectional FIFO data. This bus is normally input unless OE# is low. When high, do not read data from the FIFO. When low, there is data available in the FIFO which can be read by driving RD# low. When in synchronous mode, data is transferred on every clock that RXF# and RD# are both low. Note that the OE# pin must be driven low at least 1 clock period before asserting RD# low. When high, do not write data into the FIFO. When low, data can be written into the FIFO by driving WR# low. When in synchronous mode, data is transferred on every clock that TXE# and WR# are both low. Enables the current FIFO data byte to be driven onto D0...D7 when RD# goes low. The next FIFO data byte (if available) is fetched from the receive FIFO buffer each CLKOUT cycle until RD# goes high. Enables the data byte on the D0...D7 pins to be written into the transmit FIFO buffer when WR# is low. The next FIFO data byte is written to the transmit FIFO buffer each CLKOUT cycle until WR# goes high. 60 MHz Clock driven from the chip. All signals should be synchronized to this clock. Output enable when low to drive data onto D0-7. This should be driven low at least 1 clock period before driving RD# low to allow for data buffer turn-around. The Send Immediate / WakeUp signal combines two functions on a single pin. If USB is in suspend mode (PWREN# = 1) and remote wakeup is enabled in the EEPROM , strobing this pin low will cause the device to request a resume on the USB Bus. Normally, this can be used to wake up the Host PC. During normal operation (PWREN# = 0), if this pin is strobed low any data in the device TX buffer will be sent out over USB on the next Bulk-IN request from the drivers regardless of the pending packet size. This can be used to optimize USB transfer speed for some applications. Tie this pin to VCCIO if not used. 26 RXF# OUTPUT 27 TXE# OUTPUT 28 RD# INPUT 29 WR# INPUT 32 33 CLKOUT OE# OUTPUT INPUT 30 SIWU INPUT Table 3.5 Channel A FT245 Style Synchronous FIFO Configured Pin Descriptions For a functional description of this mode, please refer to section 4.4 FT245 Synchronous FIFO Interface Mode Description Copyright (c) 2009 Future Technology Devices International Limited 12 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 3.4.3 FT2232H pins used in an FT245 Style Asynchronous FIFO Interface The FT2232H channel A or channel B can be configured as a FT245 asynchronous FIFO interface. When configured in this mode, the pins used and the descriptions of the signals are shown in Table 3.6. To enter this mode the external EEPROM must be set to make port A or B or both 245 mode. In this mode, data is written or read on the falling edge of the RD# or WR# signals. Channel A Pin No. Channel B Pin No. Name Type FT245 Configuration Description 24,23,22,21, 19,18,17,16 46,45,44,43, 41,40,39,38 Channel A = ADBUS[7:0] Channel B = BDBUS[7:0] I/O D7 to D0 bidirectional FIFO data. This bus is normally input unless RD# is low. 26 48 RXF# OUTPUT When high, do not read data from the FIFO. When low, there is data available in the FIFO which can be read by driving RD# low. When RD# goes high again RXF# will always go high and only become low again if there is another byte to read. During reset this signal pin is tri-state, but pulled up to VCCIO via an internal 200k resistor. When high, do not write data into the FIFO. When low, data can be written into the FIFO by strobing WR# high, then low. During reset this signal pin is tristate, but pulled up to VCCIO via an internal 200k resistor. Enables the current FIFO data byte to be driven onto D0...D7 when RD# goes low. Fetches the next FIFO data byte (if available) from the receive FIFO buffer when RD# goes high. Writes the data byte on the D0...D7 pins into the transmit FIFO buffer when WR# goes from high to low. The Send Immediate / WakeUp signal combines two functions on a single pin. If USB is in suspend mode (PWREN# = 1) and remote wakeup is enabled in the EEPROM , strobing this pin low will cause the device to request a resume on the USB Bus. Normally, this can be used to wake up the Host PC. During normal operation (PWREN# = 0), if this pin is strobed low any data in the device TX buffer will be sent out over USB on the next Bulk-IN request from the drivers regardless of the pending packet size. This can be used to optimize USB transfer speed for some applications. Tie this pin to VCCIO if not used. 27 52 TXE# OUTPUT 28 53 RD# INPUT 29 54 WR# INPUT 30 55 SIWU INPUT Table 3.6 Channel A and Channel B FT245 Style Asynchronous FIFO Configured Pin Descriptions Copyright (c) 2009 Future Technology Devices International Limited 13 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 3.4.4 FT2232H pins used in a Synchronous or Asynchronous Bit-Bang Interface The FT2232H channel A or channel B can be configured as a synchronous or asynchronous bit-bang interface. Bit-bang mode is a special FTDI FT2232H device mode that changes the 8 IO lines on either (or both) channels into an 8 bit bi-directional data bus. There are two types of bit-bang modes: synchronous and asynchronous. When configured in any bit-bang mode, the pins used and the descriptions of the signals are shown in Table 3.7 Channel A Pin No. 24,23,22,21, 19,18,17,16 Channel B Pin No. 46,45,44,43, 41,40,39,38 Name Type Configuration Description Channel A = ADBUS[7:0] Channel B = BDBUS[7:0] I/O D7 to D0 bidirectional Bit-Bang parallel I/O data pins Write strobe, active low output indicates 27 52 WRSTB# OUTPUT when new data has been written to the I/O pins from the Host PC (via the USB interface). Read strobe, this output rising edge 28 53 RDSTB# OUTPUT indicates when data has been read from the parallel I/O pins and sent to the Host PC (via the USB interface). The Send Immediate / WakeUp signal combines two functions on a single pin. If USB is in suspend mode (PWREN# = 1) and remote wakeup is enabled in the EEPROM , strobing this pin low will cause the device to request a resume on the USB Bus. Normally, this can be used to wake up the Host PC. During normal operation (PWREN# = 0), if this pin is strobed low any data in the device TX buffer will be sent out over USB on the next Bulk-IN request from the drivers regardless of the pending packet size. This can be used to optimize USB transfer speed for some applications. Tie this pin to VCCIO if not used. 30 55 SIWU INPUT Table 3.7 Channel A and Channel B Synchronous or Asynchronous Bit-Bang Configured Pin Descriptions For a functional description of this mode, please refer to section 4.10 Synchronous and Asynchronous BitBang Interface Mode Description. Copyright (c) 2009 Future Technology Devices International Limited 14 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 3.4.5 FT2232H pins used in an MPSSE The FT2232H channel A and channel B each have a Multi-Protocol Synchronous Serial Engine (MPSSE). Each MPSSE can be independently configured to a number of industry standard serial interface protocols such as JTAG, I2C or SPI, or it can be used to implement a proprietary bus protocol. For example, it is possible to use one of the FT2232H's channels to connect to an SRAM configurable FPGA such as supplied by Altera or Xilinx. The FPGA device would normally be un-configured (i.e. have no defined function) at power-up. Application software on the PC could use the MPSSE to download configuration data to the FPGA over USB. This data would define the hardware function on power up. The other FT2232H channel would be available for another function. Alternatively each MPSSE can be used to control a number of GPIO pins. When configured in this mode, the pins used and the descriptions of the signals are shown Table 3.6 Channel A Pin No. Channel B Pin No. Name Type MPSSE Configuration Description Clock Signal Output. For example: 16 38 TCK/SK OUTPUT JTAG - TCK, Test interface clock SPI - SK, Serial Clock Serial Data Output. For example: 17 39 TDI/DO OUTPUT JTAG - TDI, Test Data Input SPI - DO Serial Data Input. For example: 18 40 TDO/DI INPUT JTAG - TDO, Test Data output SPI - DI, Serial Data Input Output Signal Select. For example: 19 41 TMS/CS OUTPUT JTAG - TMS, Test Mode Select SPI - CS, Serial Chip Select 21 22 23 24 26 27 28 29 30 32 33 34 43 44 45 46 48 52 53 54 55 57 58 59 GPIOL0 GPIOL1 GPIOL2 GPIOL3 GPIOH0 GPIOH1 GPIOH2 GPIOH3 GPIOH4 GPIOH5 GPIOH6 GPIOH7 I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O General Purpose input/output General Purpose input/output General Purpose input/output General Purpose input/output General Purpose input/output General Purpose input/output General Purpose input/output General Purpose input/output General Purpose input/output General Purpose input/output General Purpose input/output General Purpose input/output Table 3.8 Channel A and Channel B MPSSE Configured Pin Descriptions For a functional description of this mode, please refer to section 4.6 MPSSE Interface Mode Description. Copyright (c) 2009 Future Technology Devices International Limited 15 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 3.4.6 FT2232H Pins used as a Fast Serial Interface The FT2232H channel B can be configured for use with high-speed optical bi-directional isolated serial data transfer: Fast Serial Interface. (Not available on channel A). A proprietary FTDI protocol designed to allow galvanic isolated devices to communicate synchronously with the FT2232H using just 4 signal wires (over two dual opto-isolators), and two power lines. The peripheral circuitry controls the data transfer rate in both directions, whilst maintaining full data integrity. Maximum USB full speed data rates can be achieved. Both `A' and `B' channels can communicate over the same 4 wire interface if desired. When configured in this mode, the pins used and the descriptions of the signals are shown in Table 3.9. Channel B Pin No. 38 Name Type Fast Serial Interface Configuration Description Fast serial data input. Fast serial clock input. FSDI INPUT 39 FSCLK INPUT Clock input to FT2232H chip to clock data in or out. Fast serial data output. Fast serial Clear To Send signal output. 40 FSDO OUTPUT 41 FSCTS OUTPUT Driven low to indicate that the chip is ready to send data Table 3.9 Channel B Fast Serial Interface Configured Pin Descriptions For a functional description of this mode, please refer to section 4.8 Fast Opto-Isolated Serial Interface Mode Description Copyright (c) 2009 Future Technology Devices International Limited 16 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 3.4.7 FT2232H Pins Configured as a CPU-style FIFO Interface The FT2232H channel A or channel B can be configured in a CPU-style FIFO interface mode which allows a CPU to interface to USB via the FT2232H. This mode is enabled in the external EEPROM. When configured in this mode, the pins used and the descriptions of the signals are shown in Table 3.10 Channel A Pin No. 24,23,22,21, 19,18,17,16 26 27 28 29 Channel B Pin No. 46,45,44,43, 41,40,39,38 48 52 53 54 Name Type Fast Serial Interface Configuration Description Channel A = ADBUS[7:0] Channel B = BDBUS[7:0] CS# A0 RD# WR# I/O D7 to D0 bidirectional data bus INPUT INPUT INPUT INPUT Active low chip select input Address bit A0 Active Low FIFO Read input Active Low FIFO Write input Table 3.10 Channel A and Channel B CPU-style FIFO Interface Configured Pin Descriptions For a functional description of this mode, please refer to section 4.9 CPU-style FIFO Interface Mode Description Copyright (c) 2009 Future Technology Devices International Limited 17 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 3.4.8 FT2232H Pins Configured as a Host Bus Emulation Interface The FT2232H can be used to combine channel A and channel B to be configured as a host bus emulation interface mode which emulates a standard 8048 or 8051 MCU host. When configured in this mode, the pins used and the descriptions of the signals are shown in Table 3.11 Pin No. Name Type Fast Serial Interface Configuration Description 24,23,22,21, 19,18,17,16 34,33,32,30, 29,28,27,26 ADBUS[7:0] I/O OUTPUT Multiplexed bidirectional Address/Data bus AD7 to AD0 A[15:8] Extended Address A15 to A8 38 CS# OUTPUT Active low chip select device during Read or Write. OUTPUT 39 ALE Positive pulse to latch the address OUTPUT 40 RD# Active low read output. 41 WR# OUTPUT Active low write output. (Data is setup before WR# goes low, and is held after WR# goes high) INPUT 43 IORDY Extends the time taken to perform a Read or Write operation if driven low. Pull up to VCORE if not being used. Master clock. Outputs the clock signal being used by the configured interface. MPSSE mode instructions to set / clear or read the high byte of data can be used with this pin. Please refer to Application Note AN2232L-1 for operation of these instructions. MPSSE mode instructions to set / clear or read the high byte of data can be used with this pin. In addition this pin has instructions which will make the controller wait until it is high, or wait until it is low. This can be used to connect to an IRQ pin of a peripheral chip. The FT2232H will wait for the interrupt, and then read the device, and pass the answer back to the host PC. I/O1 must be held in input mode if this option is used. Please refer to Application Note AN2232L-1 for operation of these instructions. 44 CLKOUT OUTPUT I/O 45 I/O0 I/O 46 I/O1 Table 3.11 Channel A and Channel B Host Bus Emulation Interface Configured Pin Descriptions For a functional description of this mode, please refer to section 4.7 MCU Host Bus Emulation Mode Copyright (c) 2009 Future Technology Devices International Limited 18 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 4 Function Description th The FT2232H USB 2.0 High Speed (480Mb/s) to UART/FIFO is one of FTDI's 5 generation of Ics. It has the capability of being configured in a variety of industry standard serial or parallel interfaces. The FT2232H has two independent configurable interfaces. Each interface can be configured as UART, FIFO, JTAG, SPI, I2C or bit-bang mode with independent baud rate generators. In addition to these, the FT2232H supports a host bus emulation mode, a CPU-Style FIFO mode and a fast opto-isolated serial interface mode. 4.1 Key Features USB High Speed to Dual Interface. The FT2232H is a USB 2.0 High Speed (480Mbits/s) to dual independent flexible and configurable parallel/serial interfaces. Functional Integration. The FT2232H integrates a USB protocol engine which controls the physical Universal Transceiver Macrocell Interface (UTMI) and handles all aspects of the USB 2.0 High Speed interface. The FT222H includes an integrated +1.8V Low Drop-Out (LDO) regulator and 12MHz to 480MHz PLL. It also includes 4kbytes Tx and Rx data buffers per interface. The FT2232H effectively integrates the entire USB protocol on a chip with no firmware required. MPSSE.Multi-Purpose Synchronous Serial Engines (MPSSE), capable of speeds up to 30 Mbits/s, provides flexible synchronous interface configurations. Data Transfer rate. The FT2232H support s a data transfer rate up to 12 Mbaud when configured as an RS232/RS422/RS485 UART interface or greater than 25 Mbytes/second over a synchronous parallel FIFO interface. Latency Timer. This is really a feature of the driver and is used to as a timeout to flush short packets of data back to the PC. The default is 16ms, but it can be altered between 0ms and 256ms. At 0ms latency you get a packet transfer on every high speed microframe. 4.2 Functional Block Descriptions Dual Multi-Purpose UART/FIFO Controllers. The FT2232H has two independent UART/FIFO Controllers. These control the UART data, 245 fifo data, opto isolation (Fast Serial) or control the Bit-Bang mode if selected by SETUP command. Each Multi-Purpose UART/FIFO Controller also contain an MPSSE (Multi Protocol Synchronous Serial Engine) which can be used independently of each other. Using this MPSSE, the Multi-Purpose UART/FIFO Controller can be configured, under software command, to have 1 MPSSE + 1 UART / 245 FIFO (each UART / 245 can be set to Bit Bang mode to gain extra I/O if required) or 2 MPSSE. USB Protocol Engine and FIFO control. The USB Protocol Engine controls and manages the interface between the UTMI PHY and the FIFOs of the chip. It also handles power management and the USB protocol specification. Dual Port FIFO TX Buffer (4Kbytes per interface). Data from the Host PC is stored in these buffers to be used by the Multi-purpose UART/FIFO controllers. This is controlled by the USB Protocol Engine and FIFO control block. Dual Port FIFO RX Buffer (4Kbytes per interface). Data from the Multi-purpose UART/FIFO controllers is stored in these blocks to be sent back to the the Host PC when requested. This is controlled by the USB Protocol Engine and FIFO control block. RESET Generator - The integrated Reset Generator Cell provides a reliable power-on reset to the device internal circuitry at power up. The RESET# input pin allows an external device to reset the FT2232H. RESET# should be tied to VCCIO (+3.3v) if not being used. Independent Baud Rate Generators - The Baud Rate Generators provides a x16 or a x10 clock input to the UART's from a 120MHz reference clock and consists of a 14 bit pre-scaler and 4 register bits which provide fine tuning of the baud rate (used to divide by a number plus a fraction). This determines the Baud Rate of the UART which is programmable from 183 baud to 12 million baud. Copyright (c) 2009 Future Technology Devices International Limited 19 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 See FTDI application note AN232B-05 on the FTDI website (www.ftdichip.com) for more details. +1.8V LDO Regulator. The +1.8V LDO regulator generates the +1.8 volts for the core and the USB transceiver cell. Its input (VREGIN) must be connected to a +3.3V external power source. It is also recommended to add an external filtering capacitor to the VREGIN. There is no direct connection from the +1.8V output (VREGOUT) and the internal functions of the FT2232H. The PCB must be routed to connect VREGOUT to the pins that require the +1.8V including VREGIN. UTMI PHY. The Universal Transceiver Macrocell Interface (UTMI) physical interface cell. This block handles the Full speed / High Speed SERDES (serialise - deserialise) function for the USB TX/RX data. It also provides the clocks for the rest of the chip. A 12 MHz crystal should be connected to the OSCI and OSCO pins. A 12K Ohm resistor should be connected between REF and GND on the PCB. The UTMI PHY functions include: * * * * * * Supports 480 Mbit/s "High Speed" (HS)/ 12 Mbit/s "Full Speed" (FS), FS Only and "Low Speed" (LS) SYNC/EOP generation and checking Data and clock recovery from serial stream on the USB. Bit-stuffing/unstuffing; bit stuff error detection. Manages USB Resume, Wake Up and Suspend functions. Single parallel data clock output with on-chip PLL to generate higher speed serial data clocks. EEPROM Interface. When used without an external EEPROM the FT2232H defaults to a USB to dual asynchronous serial port device. Adding an external 93C46 (93C56 or 93C66) EEPROM allows each of the chip's channels to be independently configured as a serial UART (RS232 mode), parallel FIFO (245) mode or fast serial (opto isolation). The external EEPROM can also be used to customise the USB VID, PID, Serial Number, Product Description Strings and Power Descriptor value of the FT2232H for OEM applications. Other parameters controlled by the EEPROM include Remote Wake Up, Soft Pull Down on Power-Off and I/O pin drive strength. The EEPROM should be a 16 bit wide configuration such as a Microchip 93LC46B or equivalent capable of a 1Mbit/s clock rate at VCC = +3.00V to 3.6V. The EEPROM is programmable in-circuit over USB using a utility program called MPROG available from FTDI's web site (www.ftdichip.com). This allows a blank part to be soldered onto the PCB and programmed as part of the manufacturing and test process. If no EEPROM is connected (or the EEPROM is blank), the FT2232H will default to dual serial ports. The device uses its built-in default VID (0403) , PID (6010) Product Description and Power Descriptor Value. In this case, the device will not have a serial number as part of the USB descriptor. Copyright (c) 2009 Future Technology Devices International Limited 20 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 4.3 Dual Port FT232 UART Interface Mode Description The FT2232H can be configured in similar UART modes as the FTDI FT232 devices. The following examples illustrate how to configure the FT2232H with an RS232, RS422 or RS485 interface. The FT2232 can be configured as a mixture of these interfaces. 4.3.1 Dual Port RS232 Configuration Figure 4.1 illustrates how the FT2232H can be configured with an RS232 UART interface. This can be repeated for channel B to provide a dual RS232, but has been omitted for clarity. Figure 4.1 RS232 Configuration Copyright (c) 2009 Future Technology Devices International Limited 21 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 4.3.2 Dual Port RS422 Configuration Figure 4.2 illustrates how the FT2232H can be configured as a dual RS422 interface. FT2232H 60 PWREN# SUSPEND# TXD RXD RTS# CTS# DTR# DSR# DCD# RI# TXDEN 36 5 D 4 VCC 14 SP491 10 9 11 DB9-M RS422 Channel A TXDM_A TXDP_A RXDP_A 120R RXDM_A 16 17 18 19 21 22 23 24 26 3 2 R 6 7 VCC 14 SP491 4 10 5 3 11 2 R 6 7 VCC 14 SP491 4 10 5 3 12 120R D 9 12 GND RTSM_A RTSP_A CTSP_A CTSM_A DB9-M RS422 Channel B TXDM_B TXDP_B RXDP_B 120R RXDM_B 38 TXD 39 RXD 40 RTS# 41 CTS# 43 DTR# 44 DSR# 45 DCD# 46 RI# 48 TXDEN D 9 11 2 R 6 7 12 VCC 14 SP491 4 10 5 3 11 2 R 6 7 12 120R D 9 GND RTSM_B RTSP_B CTSP_B CTSM_B Figure 4.2 Dual RS422 Configuration In this case both channel A and channel B are configured as UART operating at TTL levels. The Sipex SP491 is used as a level converter to convert the TTL level signals from the FT2232H to RS422 levels. The PWREN# signal is used to power down the level shifters such that they operate in a low quiescent current when the USB interface is in suspend mode. Copyright (c) 2009 Future Technology Devices International Limited 22 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 4.3.3 Dual Port RS485 Configuration Figure 4.3 illustrates how the FT2232H can be configured as a dual RS485 interface. FT2232H PW REN# SUSPEND# TXD RXD RTS# CTS# DTR# DSR# DCD# R I# TXDEN 60 36 16 17 18 19 21 L IN K 22 23 24 26 8 3 7 4 2 1 R 5 120R D 6 DPA GND D M _A VCC SP481 D B 9 -M RS485 Channel A D B 9 -M RS485 Channel B 8 3 7 38 4 2 1 R 5 120R 43 D M _B D P_B GND VCC SP481 TXD 39 RXD 40 RTS# 41 CTS# DTR# 44 DSR# 45 DCD# 46 R I# 48 TXDEN D 6 L IN K Figure 4.3 Dual RS485 Configuration In this case both channel A and channel B are configured as RS485 operating at TTL levels. This example uses two Sipex SP491 devices but there are similar parts available from Maxim and Analog Devices amongst others. The SP491 is a RS485 device in a compact 8 pin SOP package. It has separate enables on both the transmitter and receiver. With RS485, the transmitter is only enabled when a character is being transmitted from the UART. The TXDEN pins on the FT2232H are provided for exactly that purpose, and so the transmitter enables are wired to the TXDEN's. The receiver enable is active low, so it is wired to the PWREN# pin to disable the receiver when in USB suspend mode. RS485 is a multi-drop network - i.e. many devices can communicate with each other over a single two wire cable connection. The RS485 cable requires to be terminated at each end of the cable. Links are provided to allow the cable to be terminated if the device is physically positioned at either end of the cable. In this example the data transmitted by the FT2232H is also received by the device that is transmitting. This is a common feature of RS485 and requires the application software to remove the transmitted data from the received data stream. With the FT2232H it is possible to do this entirely in hardware - simply modify the schematic so that RXD of the FT2232H is the logical OR of the SP481 receiver output with TXDEN using an HC32 or similar logic gate. Copyright (c) 2009 Future Technology Devices International Limited 23 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 4.4 FT245 Synchronous FIFO Interface Mode Description When channel A is configured in an FT245 Synchronous FIFO interface mode the IO timing of the signals used are shown in Figure 4.4, which shows details for read and write accesses. The timings are shown in Table 4.1. Note that only a read or a write cycle can be performed at any one time. Data is read or written on the rising edge of the CLKOUT clock. Figure 4.4 FT245 Synchronous FIFO Interface Signal Waveforms NAME t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 t14 MIN 7.5 7.5 1 1 1 1 11 0 1 11 0 11 0 NOM 16.67 8.33 8.33 MAX 7.15 7.15 7.15 7.15 7.15 Units COMMENT ns CLKOUT period ns CLKOUT high period ns CLKOUT low period ns CLKOUT to RXF# ns CLKOUT to read DATA valid ns OE# to read DATA valid ns CLKOUT to OE# ns RD# setup time (RD# low afterOE# low) ns RD# hold time ns CLKOUT TO TXE# ns Write DATA setup time ns Write DATA hold time ns WR# setup time (WR# low after TXE# low) ns WR# hold time Table 4.1 FT245 Synchronous FIFO Interface Signal Timings Copyright (c) 2009 Future Technology Devices International Limited 24 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 This single channel mode uses a synchronous interface to get high data transfer speeds. The chip drives a 60 MHz CLKOUT clock for the external system to use. Note that Asynchronous FIFO mode must be selected on both channels before selecting the Synchronous FIFO mode in software. 4.4.1 FT245 Synchronous FIFO Read Operation A read operation is started when the chip drives RXF# low. The external system can then drive OE# low to turn around the data bus drivers before acknowledging the data with the RD# signal going low. The first data byte is on the bus after OE# is low. The external system can burst the data out of the chip by keeping RD# low or it can insert wait states in the RD# signal. If there is more data to be read it will change on the clock following RD# sampled low. Once all the data has been consumed, the chip will drive RXF# high. Any data that appears on the data bus, after RXF# is high, is invalid and should be ignored. 4.4.2 FT245 Synchronous FIFO Write Operation A write operation can be started when TXE# is low. WR# is brought low when the data is valid. A burst operation can be done on every clock providing TXE# is still low. The external system must monitor TXE# and its own WR# to check that data has been accepted. Both TXE# and WR# must be low for data to be accepted. Copyright (c) 2009 Future Technology Devices International Limited 25 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 4.5 FT245 Asynchronous FIFO Interface Mode Description The FT2232H can be configured as a dual channel asynchronous FIFO interface. This mode is similar to the synchronous FIFO interface with the exception that the data is written to or read from the FIFO on the falling edge of the WR# or RD# signals. This mode does not provide a CLKOUT signal and it does not expect an OE# input signal. The following diagrams illustrate the asynchronous FIFO mode timing. Figure 4.5 FT245 asynchronous FIFO Interface READ Signal Waveforms Figure 4.6 FT245 asynchronous FIFO Interface WRITE Signal Waveforms Time Description RD# input pulse width RD# to RD pre-charge RD# input active to data output valid Valid data hold time after RD# input rising edge RD# inactive to RXF# output inactive RXF# output inactive after RD# cycle WR# active pulse width Min 50 T5 +T6 20 0 0 33 10 Max ns ns 50 ns ns 25 67 ns ns ns Units T1 T2 T3 T4 T5 T6 T7 Copyright (c) 2009 Future Technology Devices International Limited 26 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 T8 T9 T10 T11 T12 WR# to WR# pre-charge time Data setup time before WR# input falling edge Data hold time from WR# input falling edge WR# inactive to TXE# output active TXE# input inactive after WR# cycle 50 20 10 10 49 ns ns ns 25 84 ns ns Table 4.2 Asynchronous FIFO Timings (based on standard drive level outputs) Copyright (c) 2009 Future Technology Devices International Limited 27 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 4.6 MPSSE Interface Mode Description. MPSSE Mode is designed to allow the FT2232H to interface efficiently with synchronous serial protocols such as JTAG, I2C and SPI Bus. It can also be used to program SRAM based FPGA's over USB. The MPSSE interface is designed to be flexible so that it can be configured to allow any synchronous serial protocol (industry standard or proprietary) to be implemented using the FT2232H. MPSSE is available on channel A and channel B. MPSSE is fully configurable, and is programmed by sending commands down the data stream. These can be sent individually or more efficiently in packets. MPSSE is capable of a maximum sustained data rate of 30 Mbits/s. When a channel is configured in MPSSE mode, the IO timing and signals used are shown in Figure 4.7 and Table 4.3 These show timings for CLKOUT=30MHz. CLKOUT can be divided internally to be provide a slower clock. Figure 4.7 MPSSE Signal Waveforms NAME t1 t2 t3 t4 t5 t6 MIN 15 15 1 0 11 NOM 33.33 16.67 16.67 MAX 7.15 Units ns ns ns ns ns COMMENT CLKOUT period CLKOUT high period CLKOUT low period CLKOUT to TDI/DO delay TDO/DI hold time TDO/DI setup time Table 4.3 MPSSE Signal Timings MPSSE mode is enabled using Set Bit Bang Mode driver command. A hex value of 2 will enable it, and a hex value of 0 will reset the device. See application note AN2232L-02, "Bit Mode Functions for the FT2232D" for more details and examples. The MPSSE command set is fully described in application note AN_108 - "Command Processor For MPSSE and MCU Host Bus Emulation Modes". The following additional application notes are available for configuring the MPSSE : * * * AN_109 - "Programming Guide for High Speed FTCI2C DLL" AN_110 - "Programming Guide for High Speed FTCJTAG DLL" AN_111 - "Programming Guide for High Speed FTCSPI DLL" Copyright (c) 2009 Future Technology Devices International Limited 28 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 4.7 MCU Host Bus Emulation Mode MCU host bus emulation mode uses both of the FT2232H's A and B channel interfaces to make the chip emulate a standard 8048/8051 MCU host bus. This allows peripheral devices for these MCU families to be directly connected to USB via the FT2232H. The lower 8 bits (AD7 to AD0) is a multiplexed Address / Data bus. A15 to A18 provide upper (extended) addresses. There are 4 basic operations:1) Read (does not change A15 to A8) 2) Read Extended (changes A15 to A8) 3) Write (does not change A15 to A8) 4) Write Extended (changes A15 to A8) MCU Host Bus Emulation mode is enabled using Set Bit Bang Mode driver command. A hex value of 8 will enable it, and a hex value of 0 will reset the device. The FT2232H operates in the same way as the FT2232D. See application note AN2232-02, "Bit Mode Functions for the FT2232D" for more details and examples. The MCU Host Bus Emulation Mode command set is fully described in application note AN_108 - "Command Processor For MPSSE and MCU Host Bus Emulation Modes". When MCU Host Bus Emulation mode is enabled the IO signal lines on both channels work together and the pins are configured as described in Table 3.11. The following sections give some details of the read and write cycle waveforms and timings. The CLKOUT output clock can operate up to 60MHz. In Host Bus Emulation mode the clock divisor has no effect. The clock divisor is used for serial data and is a different part of the MPSSE block. In host bus emulation the 60MHz clock is always output and doesn't change with any commands. Copyright (c) 2009 Future Technology Devices International Limited 29 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 4.7.1 MCU Host Bus Emulation Mode Signal Timing - Write Cycle Figure 4.8 MCU Host Bus Emulation Mode Signal Waveforms - write cycle NAME t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 Description High address byte is placed on the bus if the extended write is used Low address byte is put out. 1 clock period for address is set up. ALE goes high to enable latch. This will extend to 2 clocks wide if IORDY is low. ALE goes low to latch address and CS# is set active low. Data driven onto the bus. 1 clock period for data setup. WR# is driven active low. This will extend to 6 clocks wide if IORDY is low. WR# is driven inactive high. CS# is driven inactive, 1/2 a clock period after WR# goes inactive Data is held until this point, and may now change Table 4.4 MCU Host Bus Emulation Mode Signal Timings - write cycle The IORDY "WAIT" states in the read and write cycles assume that the "divide-by-5" has been set in the clock generation. (This can be set by sending the hex value $8A) Copyright (c) 2009 Future Technology Devices International Limited 30 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 4.7.2 MCU Host Bus Emulation Mode Signal Timing - Read Cycle Figure 4.9 MCU Host Bus Emulation Mode Signal Waveforms - read cycle NAME t1 t2 t3 t4 Description High address byte is placed on the bus if the extended read is used - otherwise t1 will not occur. Low address byte is put out. 1 clock period for address set up. ALE goes high to enable address latch. This will extend to 2 clocks wide if IORDY is low. ALE goes low to latch address, and CS# is set active low. This will extend to 3 clocks if IORDY is sampled low. CS# will always drop 1 clock after ALE has gone high no matter the state of IORDY. Data is set as input (Hi-Z), and RD# is driven active low. 1 clock period for data setup. This will extend to 5 clocks wide if IORDY# is sampled low. RD# is driven inactive high. CS# is driven inactive 1/2 a clock period after RD# goes inactive, and the data bus is set back to output. t5 t6 t7 t8 t9 Table 4.5 MCU Host Bus Emulation Mode Signal Timings- read cycle An example of the MCU Host Emulation Interface enabling a USB interface to CAN Bus using a CANBus Controller is shown in Figure 4.10 FT2232H CS# ALE RD# W R# CS# ALE/AS RD# W R# SJA1000 CAN Bus Controller Tx CANB us Transeiver Rx AD [7:0] ADD RESS / DATA BUS AD [7:0] C AN Bus Vcc Vcc IOR DY# I/O0 I/O 1 MO DE INT# Figure 4.10 MCU Host Emulation Example using a CANBus Controller Copyright (c) 2009 Future Technology Devices International Limited 31 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 4.8 Fast Opto-Isolated Serial Interface Mode Description Fast Opto-Isolated Serial Interface Mode provides a method of communicating with an external device over USB using 4 wires that can have opto-isolators in their path, thus providing galvanic isolation between systems. If either channel A or channel B is enabled in Fast Opto-Isolated Serial mode then the pins on channel B are switched to the fast serial interface configuration. The I/O interface for fast serial mode is always on channel B, even if both channels are being used in this mode. An address bit is used to determine the source or destination channel of the data. It therefore makes sense to always use at least channel B or both for fast serial mode, but not A own its own. Fast serial mode is enabled by setting the appropriate bits in the external EEPROM. The fast serial mode can be held in reset by setting a bit value of 10 using the Set Bit Bang Mode command. While this bit is set the device is held reset - data can be sent to the device, but it will not be sent out by the device until the device is enabled again. This is done by sending a bit value of 0 using the set bit mode command. See application note AN2232L-02, "Bit Mode Functions for the FT2232D" for more details and examples. When either Channel B or both Channel A and B are configured in Fast Opto-Isolated Serial Interface mode the IO timing of the signals used are shown in Figure 4.11 and the timings are shown in Table 4.6 Figure 4.11 Fast Opto-Isolated Serial Interface Signal Waveforms NAME t1 t2 t3 t4 t5 t6 t7 MIN 5 5 5 10 10 10 20 NOM MAX Units ns ns ns ns ns ns ns COMMENT FSDO/FSCTS hold time FSDO/FSCTS setup time FSDI hold time FSDI Setup Time FSCLK low FSCLK high FSCLK Period Table 4.6 Fast Opto-Isolated Serial Interface Signal Timings Copyright (c) 2009 Future Technology Devices International Limited 32 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 4.8.1 Outgoing Fast Serial Data To send fast serial data out of the FT2232H, the external device must drive the FSCLK clock. If the FT2232H has data ready to send, it will drive FSDO output low to indicate the start bit. It will not do this if it is currently receiving data from the external device. This is illustrated in Figure 4.12. FSCLK FSDO 0 Start Bit D0 D1 D2 D3 D4 D5 D6 D7 SRCE Source Bit Data Bits - LSB first Figure 4.12 Fast Opto-Isolated Serial Interface Output Data Notes :1. The first bit output (Start bit) is always 0. 2. FSDO is always sent LSB first. 3. The last serial bit output is the source bit (SRCE). It indicates which channel the data has come from. A `0' means that it has come from Channel A, a `1' means that it has come from Channel B. 4. If the target device is unable to accept the data when it detects the START bit, it should stop the FSCLK until it can accept the data. 4.8.2 Incoming Fast Serial Data An external device is allowed to send data into the FT2232H if FSCTS is high. On receipt of a zero START bit on FSDI, the FT2232H will drop FSCTS on the next positive clock edge. The data from bits 0 to 7 are then clocked in (LSB first). The last bit (DEST) determines where the data will be written to. The data can be sent to either channel A or to channel B. If DEST= `0', the data is sent to channel A, (assuming channel A is enabled for fast serial mode, otherwise the data is sent to channel B). If DEST= `1' the data is sent to channel B, (assuming channel B is enabled for fast serial mode, otherwise the data will go to channel A. (Either channel A, channel B or both channels must be enabled as fast serial mode or the function is disabled). This is illustrated in Figure 4.13. FSCTS FSCLK FSDI 0 Start Bit D0 D1 D2 D3 D4 D5 D6 D7 DEST Destination Bit Data Bits - LSB first Figure 4.13 Fast Opto-Isolated Serial Interface Input Data Notes :1. The first bit input (Start bit) is always 0. 2. FSDI is always received LSB first. 3. The last received serial bit is the destination bit (DEST).It indicates which channel the data should go to. A `0' means that it should go to channel A, a `1' means that it should go to channel B. 4. The target device should ensure that CTS is high before it sends data. CTS goes low after data bit 0 (D0) and stays low until the chip can accept more data. Copyright (c) 2009 Future Technology Devices International Limited 33 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 4.8.3 Fast Opto-Isolated Serial Data Interface Example The following example,Figure 4.14 , shows two Agilent HCPL-2430 (see the semiconductor section at www.agilent.com) high speed opto-couplers used to optically isolate an external device which interfaced to USB using the FT2232H. In this example VCC5V is the USB VBUS supply and VCCE is the supply to the external device. Care must be taken with the voltage used to power the photo-LED's. It must be the same voltage as that the FT2232H I/Os are driving to, or the LED's may be permanently on. Limiting resistors should be fitted in the lines that drive the diodes. The outputs of the opto-couplers are open-collector and require a pull-up resistor. VCC5V Cable 8 VCCE FT2232H 1K FSDI HCPL-2430 1 470R 1K 7 6 5 2 3 470R 4 DI CLK FSCLK VCCE VCC5V 1 470R FSDO FSCTS 470R 4 HCPL-2430 8 1K 7 6 1K DO CTS 2 3 5 Figure 4.14 Fast Opto-Isolated Serial Interface Example Copyright (c) 2009 Future Technology Devices International Limited 34 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 4.9 CPU-style FIFO Interface Mode Description CPU-style FIFO interface mode is designed to allow a CPU to interface to USB via the FT2232H. This mode is enabled in the external EEPROM. The interface is achieved using a chip select bit (CS#) and address bit (A0). When either Channel A or Channel B are in CPU-style Interface mode the IO signal lines are configured as given in Table 3.10. This mode uses a combination of CS# and A0 to determine the operation to be carried out. The following truth-table, Table 4.7, gives the decode values for particular operations. CS# 1 0 0 A0 X 0 1 RD# X Read Data Pipe Read Status WR# X Write Data Pipe Send Immediate Table 4.7 CPU-Style FIFO Interface Operation Select The Status read is shown in Table 4.8 Data Bit bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 Data 1 1 1 1 X X X X Status Data available (=RXF) Space available (=TXE) Suspend Configured X X X X Table 4.8 CPU-Style FIFO Interface Operation Read Status Description Note that bits 7 to 4 can be arbitrary values and that X= not used. The timing of reading and writing in this mode is shown in Figure 4.15 and Table 4.9. A0 CS# WR# RD# D7..0 t2 t3 t1 Valid Valid t4 t6 Valid t5 t7 Valid Figure 4.15 CPU-Style FIFO Interface Operation Signal Waveforms. Copyright (c) 2009 Future Technology Devices International Limited 35 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 NAME t1 t2 t3 t4 t5 t6 t7 t8 t9 MIN 15 15 20 5 5 15 15 5 0 NOM MAX 50 30 Units ns ns ns ns ns ns ns ns ns COMMENT A0 / CS Setup to WR# Data setup to WR# WR# Pulse width A0/CS Hold from WR# Data hold from WR# A0/CS Setup to RD# Data delay from RD# A0/CS hold from RD# Data hold time from RD# Table 4.9 CPU-Style FIFO Interface Operation Signal Timing. An example of the CPU-style FIFO interface connection is shown in Figure 4.16 FT2232H Channel A or B D0 D1 D2 D3 D4 D5 D6 D7 RD# WR# A0 CS# SI / WU PWREN# ( Optional ) ( Optional ) Microcontroller IO10 IO11 IO12 IO13 IO14 IO15 IO16 IO17 IO20 IO21 IO22 IO23 IO24 IO25 Figure 4.16 CPU-Style FIFO Interface Example Copyright (c) 2009 Future Technology Devices International Limited IO Port 2 IO Port 1 36 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 4.10 Synchronous and Asynchronous Bit-Bang Interface Mode Description The FT2232H channel A or channel B can be configured as a bit-bang interface. There are two types of bit-bang modes: synchronous and asynchronous. Asynchronous Bit-Bang Mode Asynchronous Bit-Bang mode is the same as BM-style Bit-Bang mode, except that the internal RD# and WR# strobes (RDSTB# and WRSTB#) are now brought out of the device to allow external logic to be clocked by accesses to the bit-bang IO bus. On either or both channels any data written to the device in the normal manner will be self clocked onto the data pins (those which have been configured as outputs). Each pin can be independently set as an input or an output. The rate that the data is clocked out at is controlled by the baud rate generator. For the data to change there has to be new data written, and the baud rate clock has to tick. If no new data is written to the channel, the pins will hold the last value written. Synchronous Bit-Bang Mode The synchronous Bit-Bang mode will only update the output parallel port pins whenever data is sent from the USB interface to the parallel interface. When this is done, the WRSTB# will activate to indicate that the data has been read from the USB Rx FIFO buffer and written out on the pins. Data can only be received from the parallel pins (to the USB Tx FIFO interface) when the parallel interface has been written to. With Synchronous Bit-Bang mode data will only be sent out by the FT2232H if there is space in the FT2232H USB TXFIFO for data to be read from the parallel interface pins. This Synchronous Bit-Bang mode will read the data bus parallel I/O pins first, before it transmits data from the USB RxFIFO. It is therefore 1 byte behind the output, and so to read the inputs for the byte that you have just sent, another byte must be sent. For example :(1) Pins start at 0xFF Send 0x55,0xAA Pins go to 0x55 and then to 0xAA Data read = 0xFF,0x55 (2) Pins start at 0xFF Send 0x55,0xAA,0xAA (repeat the last byte sent) Pins go to 0x55 and then to 0xAA Data read = 0xFF,0x55,0xAA Synchronous Bit-Bang Mode differs from Asynchronous Bit-Bang mode in that the device parallel output is only read when the parallel output is written to by the USB interface. This makes it easier for the controlling program to measure the response to a USB output stimulus as the data returned to the USB interface is synchronous to the output data. Asynchronous Bit-Bang mode is enabled using Set Bit Bang Mode driver command. A hex value of 1 will enable Asynchronous Bit-Bang mode. Synchronous Bit-Bang mode is enabled using Set Bit Bang Mode driver command. A hex value of 4 will enable Synchronous Bit-Bang mode. See application note AN2232-02, "Bit Mode Functions for the FT2232" for more details and examples of using the bit-bang modes. An example of the synchronous bi-bang mode timing is shown in Figure 4.17 Copyright (c) 2009 Future Technology Devices International Limited 37 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 Figure 4.17 Synchronous Bit-Bang Mode Timing Interface Example NAME t1 t2 t3 t4 t5 t6 Description Current pin state is read RDSTB# is set inactive and data on the paralle I/O pins is read and sent to the USB host. RDSTB# is set active again, and any pins that are output will change to their new data 1 clock cycle to allow for data setup WRSTB# goes active. This indicates that the host PC has written new data to the I/O parallel data pins WRSTB# goes inactive Table 4.10 Synchronous Bit-Bang Mode Timing Interface Example Timings WRSTB# = this output indicates when new data has been written to the I/O pins from the Host PC (via the USB interface). RDSTB# = this output rising edge indicates when data has been read from the I/O pins and sent to the Host PC (via the USB interface). The WRSTB# goes active in t4. The WRSTB# goes active when data is read from the USB RXFIFO (i.e. sent from the PC). The RDSTB# goes inactive when data is sampled from the pins and written to the USB TXFIFO (i.e. sent to the PC). The SETUP command to the FT2232H is used to setup the bit-mode. This command also contains a byte wide data mask to set the direction of each bit. The direction on each pin doesn't change unless a new SETUP command is used to modify the direction. The WRSTB# and RDSTB# strobes are only a guide to what may be happening depending on the direction of the bus. For example if all pins are configured as inputs, it is still necessary to write to these pins in order to get the FT2232H to read those pins even though the data written will never appear on the pins. Signals and data-flow are illustrated in Figure 4.18 Figure 4.18 Bit-bang Mode Dataflow Illustration Diagram. Copyright (c) 2009 Future Technology Devices International Limited 38 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 4.11 RS232 UART Mode LED Interface Description When configured in UART mode the FT2232H has two IO pins on each channel dedicated to controlling LED status indicators, one for transmitted data the other for received data. When data is being transmitted / received the respective pins drive from tri-state to low in order to provide indication on the LED's of data transfer. A digital one-shot timer is used so that even a small percentage of data transfer is visible to the end user. VCCIO TX RX 220R 220R FT2232H TXLED# RXLED# Figure 4.19 Dual LED UART Configuration Figure 4.19 shows a configuration using two individual LED's - one for transmitted data the other for received data. VCCIO LED 220R FT2232H TXLED# RXLED# Figure 4.20 Single LED UART Configuration In Figure 4.20 the transmit and receive LED indicators are wire-OR'ed together to give a single LED indicator which indicates any transmit or receive data activity. Note that the LED's are connected to the same supply as VCCIO. Copyright (c) 2009 Future Technology Devices International Limited 39 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 4.12 FT2232H Mode Selection The 2 channels of the FT2232H reset to 2 asynchronous serial interfaces. Following a reset the required mode of each channel is determined by the contents of the EEPROM (programmed using MPROG V3.4a or later). The EEPROM contents determine if the 2 channels have been configured as FT232 asynchronous serial interface, FT245 FIFO interface, CPU-style FIFO interface or Fast Serial Interface. Following a reset, the EEPROM is read to determine which mode is configured. After device enumeration, an FT_SetBitMode command (refer to D2XX_Programmers_Guide) can be sent to the USB driver to switch the selected interface into the required mode - asynchronous bit-bang, synchronous bit-bang or MPSSE. When in FT245 FIFO mode, the FT_SetBitMode command can be used to select either Synchronous FIFO (FT_SetBitMode = 0x40) or Asynchronous FIFO mode. (Note that Asynchronous FIFO mode must be selected on both channels before selecting the Synchronous FIFO mode. This means that an EEPROM is needed to initially configure Asynchronous FIFO mode before software configures the Synchronous FIFO mode). When Synchronous FIFO mode selected, channel A uses all the memory resources of channel B. As such channel B is then not available. In this case the state of the channel B pins is determined when the configuration is switched to Asynchronous FIFO mode. If channel B had not been used for any data transfer before configuration of Asynchronous FIFO mode, then the channel B pins will remain in their default mode (D7:0=tri-stated but pulled high trough 75K resistor, TXE# =low, RXF# =high. RD# and WR# are inputs and should be pulled high). An MPSSE command, set_data_bits can be used to configure the channel B pins as inputs before configuring channel A as Synchronous FIFO. This avoids the channel B pins driving against any interfaces (such as SPI) which may have been configured previous to any switching of channel A to Synchronous FIFO mode. Refer to http://www.ftdichip.com/Documents/AppNotes/AN2232C01_MPSSE_Cmnd.pdf for the set_data_bits command and further information on the MPSSE used in MCU Host BUS Emulation mode. The MPSSE can be configured directly using the D2XX commands. The D2XX_Programmers_Guide is available from the FTDI website at http://www.ftdichip.com/Documents/ProgramGuides/D2XX_Programmer's_Guide(FT_000071).pdf The application note AN_108 - "Command Processor For MPSSE and MCU Host Bus Emulation Modes" gives further explanation and examples for the MPSSE. 4.12.1 Do I need an EEPROM? The following table Table 4.11summarises what modes are configurable using the EEPROM or the application software. ASYNC Serial UART ASYNC 245 FIFO SYNC 245 FIFO ASYNC Bitbang SYNC Bitbang MPSSE Fast Serial interface CPUStyle FIFO Host Bus Emulation EEPROM configured Application Software configured YES YES YES YES YES YES YES YES YES YES Table 4.11 Configuration Using EEPROM and Application Software Copyright (c) 2009 Future Technology Devices International Limited 40 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 5 5.1 Devices Characteristics and Ratings Absolute Maximum Ratings The absolute maximum ratings for the FT2232H devices are as follows. These are in accordance with the Absolute Maximum Rating System (IEC 60134). Exceeding these values may cause permanent damage to the device. Parameter Value Unit Storage Temperature Floor Life (Out of Bag) At Factory Ambient (30C / 60% Relative Humidity) Ambient Operating Temperature (Power Applied) MTTF FT2232HL MTTF FT2232HQ VCORE Supply Voltage VCCIO IO Voltage DC Input Voltage - USBDP and USBDM DC Input Voltage - High Impedance Bi-directionals (powered from VCCIO) DC Input Voltage - All Other Inputs such as PWREN#, SUSPEND#, RESET#, EECS, EECLK, EEDATA DC Output Current - Outputs Table 5.1 Absolute Maximum Ratings -65C to 150C 168 Hours (IPC/JEDEC J-STD-033A MSL Level 3 Compliant)* -40C to 85C TBD TBD -0.3 to +2.0 -0.3 to +4.0 -0.5 to +3.63 Degrees C Hours Degrees C hours hours V V V -0.3 to +5.8 V -0.5 to + (VCCIO +0.5) V 16 mA * If devices are stored out of the packaging beyond this time limit the devices should be baked before use. The devices should be ramped up to a temperature of +125C and baked for up to 17 hours. Copyright (c) 2009 Future Technology Devices International Limited 41 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 5.2 DC Characteristics The I/O pins are +3.3v cells, which are +5V tolerant (except the USB PHY pins). DC Characteristics (Ambient Temperature = -40C to +85C) Parameter Description Minimum Typical Maximum Units Conditions VCORE VCC Core Operating Supply Voltage VCCIO Operating Supply Voltage VREGIN Voltage regulator Input Voltage regulator Output Regulator Current Core Operating Supply Current 1.62 1.80 1.98 V Cells are 5V tolerant VCCIO* 2.97 3.30 3.63 V VREGIN 3.00 3.30 3.60 V VREGOUT Ireg 1.71 1.80 1.89 150 V mA VREGIN +3.3V VCORE = +1.8V Normal Operation VCORE = +1.8V Icc1 --- 70 --- mA Icc1r Core Reset Supply Current --- 5 --- mA Device in reset state VCORE = +1.8V USB Suspend Icc1s Core Suspend Supply Current 500 A Table 5.2 Operating Voltage and Current (except PHY) *NOTE: Failure to connect all VCCIO pins will result in failure of the device. Copyright (c) 2009 Future Technology Devices International Limited 42 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 The I/O pins are +3.3v cells, which are +5V tolerant (except the USB PHY pins). Parameter Description Minimum Typical Maximum Units Conditions V 2.40 Ioh = +/-2mA I/O Drive strength* = 4mA 3.14 3.20 Voh Output Voltage High V I/O Drive strength* = 8mA I/O Drive strength* = 12mA I/O Drive strength* = 16mA Iol = +/-2mA I/O Drive strength* = 4mA 3.22 V 3.22 V V 0.18 0.40 0.12 Vol Output Voltage Low V I/O Drive strength* = 8mA I/O Drive strength* = 12mA I/O Drive strength* = 16mA LVTTL 0.08 V 0.07 Input low Switching Threshold Input High Switching Threshold Switching Threshold Schmitt trigger negative going threshold voltage Schmitt trigger positive going threshold voltage 0.80 V Vil - 0.80 V Vih Vt Vt- 2.00 - V V - LVTTL LVTTL 1.50 1.10 V Vt+ 1.60 40 40 15 75 75 45 +/-10 2.00 V K K Vin = 0 Vin =VCCIO Vin = 0 Vin = 5.5V or 0 Rpu Rpd Iin Ioz Input pull-up resistance Input pull-down resistance Input Leakage Current 190 190 85 A A Tri-state output leakage current Table 5.3 I/O Pin Characteristics VCCIO = +3.3V (except USB PHY pins) * The I/O drive strength and slow slew-rate are configurable in the EEPROM. Copyright (c) 2009 Future Technology Devices International Limited 43 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 DC Characteristics (Ambient Temperature = -40C to +85C) Parameter Description Minimum Typical Maximum Units Conditions VPHY, VPLL Iccphy PHY Operating Supply Voltage PHY Operating Supply Current PHY Operating Supply Current 3.0 3.3 3.6 V 3.3V I/O High-speed operation at 480 MHz USB Suspend --- 30 60 mA Iccphy (susp) --- 10 50 A Table 5.4 PHY Operating Voltage and Current Parameter Description Minimum Typical Maximum Units Conditions Voh Vol Vil Output Voltage High Output Voltage Low Input low Switching Threshold Input High Switching Threshold VCORE0.2 0.2 0.8 V V V Vih 2.0 - V Table 5.5 PHY I/O Pin Characteristics Copyright (c) 2009 Future Technology Devices International Limited 44 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 6 FT2232H Configurations The following sections illustrate possible USB power configurations for the FT2232H. All USB power configurations illustrated apply to both package options for the FT2232H device 6.1 USB Bus Powered Configuration Bus Powered Application example 1: Bus powered configuration Figure 6.1 Bus Powered Configuration Example 1 Figure 6.1 illustrates the FT2232H in a typical USB bus powered design configuration. A USB bus powered device gets its power from the USB bus. In this application, the FT2232H requires that the VBUS (USB +5V) is regulated down to +3.3V (using an LDO) to supply the VCCIO, VPLL, VPHY and VREGIN. VREGIN is the +3.3V input to the on chip +1.8V regulator. The output of the on chip LDO regulator (+1.8V) drives the FT2232H core supply (VCORE). This requires a minimum of a 3.3uF filter capacitor. Copyright (c) 2009 Future Technology Devices International Limited 45 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 Bus Powered Application example 2: Bus powered configuration (with additional 1.8V LDO voltage regulator for VCORE) +3.3V +3.3V LDO +1.8V Vin Vout GND 100nF GND GND 64 VCORE 37 VCORE 12 VCORE 9 VPLL VPHY 4 LDO +3.3V Vin Vout GND +3.3V 50 VREGIN 49 VREGOUT 100nF GND 56 VCCIO 42 VCCIO 31 VCCIO 20 VCCIO +1.8V 4.7uF 4.7uF 100nF 100nF GND GND GND GND 100nF 100nF 100nF GND GND GND 100nF 100nF 100nF 100nF GND GND GND +1.8V +1.8V +1.8V +3.3V +3.3V +3.3V +3.3V GND +1.8V +3.3V 100nF GND VBUS DD+ GND 1 2 3 4 GND 100nF GND 7 8 6 +3.3V 14 1K 12K +3.3V GND DM DP REF RESET# ADBUS0 ADBUS1 ADBUS2 ADBUS3 ADBUS4 ADBUS5 ADBUS6 ADBUS7 ACBUS0 ACBUS1 ACBUS2 ACBUS3 ACBUS4 ACBUS5 ACBUS6 ACBUS7 BDBUS0 BDBUS1 BDBUS2 BDBUS3 BDBUS4 BDBUS5 BDBUS6 BDBUS7 16 17 18 19 21 22 23 24 26 27 28 29 30 32 33 34 38 39 40 41 43 44 45 46 48 52 53 54 55 57 58 59 60 36 0? GND 10K 10K 10K EECLK EEDATA 63 62 61 2 EECS EECLK EEDATA OSCI +3.3V 1 6 3 2 5 8 CS VCC ORG 4 D Q 93C46 SCL 7 DU GND BCBUS0 BCBUS1 BCBUS2 BCBUS3 BCBUS4 BCBUS5 BCBUS6 BCBUS7 GND GND GND GND GND GND GND GND PWREN# SUSPEND# 1 2.2K 3 12MHz 3 13 27pF GND OSCO TEST AGND 10 51 47 35 25 15 11 5 1 27pF GND GND GND Figure 6.2 Bus Powered Configuration Example 2 Figure 6.3 illustrates the FT2232H in a typical USB bus powered configuration similar to Figure 6.1. The difference here is that the +1.8V for the FT2232H core (VCORE) has been regulated from the VBUS as well as the +3.3V supply to the VPLL, VPHY, VCCIO and VREGIN. Copyright (c) 2009 Future Technology Devices International Limited 46 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 6.2 USB Self Powered Configuration Self Powered application example 1: Self powered configuration +3.3V +1.8V +1.8V +1.8V +3.3V +3.3V +3.3V +3.3V +3.3V 100nF 100nF 100nF 4.7uF GND 4.7uF GND 100nF 100nF GND GND GND GND GND 100nF 100nF 100nF 100nF GND GND GND GND +1.8V +3.3V Ext. Power Supply LDO +3.3V 1 2 GND 100nF GND GND VBUS DD+ GND 1 2 3 4 VBUS 7 8 6 +3.3V 0? GND 12K +3.3V GND 1K 14 DM DP REF RESET# GND GND 100nF 3.3uF Vin Vout GND +3.3V 50 VREGIN +1.8V 49 VREGOUT 9 VPLL VPHY 4 VCCIO 56 42 VCCIO 31 VCCIO 20 VCCIO 64 VCORE 37 VCORE 12 VCORE ADBUS0 ADBUS1 ADBUS2 ADBUS3 ADBUS4 ADBUS5 ADBUS6 ADBUS7 ACBUS0 ACBUS1 ACBUS2 ACBUS3 ACBUS4 ACBUS5 ACBUS6 ACBUS7 BDBUS0 BDBUS1 BDBUS2 BDBUS3 BDBUS4 BDBUS5 BDBUS6 BDBUS7 16 17 18 19 21 22 23 24 26 27 28 29 30 32 33 34 38 39 40 41 43 44 45 46 48 52 53 54 55 57 58 59 60 36 10K 10K 10K EECLK EEDATA 63 62 61 2 EECS EECLK EEDATA OSCI +3.3V 1 6 3 2 5 8 4 7 2.2K 1 3 12MHz 3 13 OSCO TEST GND GND GND GND GND GND GND GND AGND CS VCC ORG D Q 93C46 SCL DU GND BCBUS0 BCBUS1 BCBUS2 BCBUS3 BCBUS4 BCBUS5 BCBUS6 BCBUS7 PWREN# SUSPEND# VBUS 4.7K 10K 10 51 47 35 25 15 11 5 1 27pF GND GND 27pF GND GND GND Figure 6.3 Self Powered Configuration Example 1 Figure 6.3 illustrates the FT2232H in a typical USB self powered configuration. A USB self powered device gets its power from its own power supply and does not draw current from the USB bus. In this example an external power supply is used. This external supply is regulated to +3.3V. Note that in this set-up, the EEPROM should be configured for self-powered operation and the option "suspend on DBUS7 low" selected in MPROG. Also this configuration uses the pin BCBUS7, so this assumes that MPSSE mode is not selected. Copyright (c) 2009 Future Technology Devices International Limited 47 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 Self Powered application example 2: Self powered configuration (with additional 1.8V LDO voltage regulator for VCORE) +3.3V +3.3V LDO +1.8V Vin Vout GND 100nF Ext. Power Supply GND GND 100nF GND +1.8V 4.7uF 4.7uF 100nF 100nF GND GND GND GND +1.8V +1.8V +1.8V +3.3V +3.3V +3.3V +3.3V 100nF 100nF 100nF GND GND GND 100nF 100nF 100nF 100nF GND GND GND GND +1.8V +3.3V VCCIO 56 42 VCCIO 31 VCCIO 20 VCCIO 64 VCORE 37 VCORE 12 VCORE 9 VPLL VPHY 4 LDO +3.3V 1 2 GND 100nF GND GND VBUS DD+ GND 1 2 3 VBUS Vin Vout GND +3.3V 50 VREGIN 49 VREGOUT 100nF GND 7 8 6 +3.3V 14 1K 12K +3.3V GND ADBUS0 ADBUS1 ADBUS2 ADBUS3 ADBUS4 ADBUS5 ADBUS6 ADBUS7 ACBUS0 ACBUS1 ACBUS2 ACBUS3 ACBUS4 ACBUS5 ACBUS6 ACBUS7 BDBUS0 BDBUS1 BDBUS2 BDBUS3 BDBUS4 BDBUS5 BDBUS6 BDBUS7 16 17 18 19 21 22 23 24 26 27 28 29 30 32 33 34 38 39 40 41 43 44 45 46 48 52 53 54 55 57 58 59 60 36 DM DP REF RESET# 0? GND 10K 10K 10K EECLK EEDATA 63 62 61 2 EECS EECLK EEDATA OSCI +3.3V 1 6 3 2 5 8 1 2.2K 3 12MHz 3 13 OSCO TEST GND GND GND GND GND GND GND GND AGND CS VCC ORG 4 D Q 93C46 SCL 7 DU GND BCBUS0 BCBUS1 BCBUS2 BCBUS3 BCBUS4 BCBUS5 BCBUS6 BCBUS7 PWREN# SUSPEND# VBUS 4.7K 10K 10 51 47 35 25 15 11 5 1 27pF GND GND 27pF GND GND GND Figure 6.4 Self Powered Configuration Example 2 Figure 6.4 illustrates the FT2232H in a typical USB self powered configuration similar to Figure 6.3. The difference here is that the +1.8V for the FT2232H core has been regulated from the external power supply. Note that in this set-up, the EEPROM should be configured for self-powered operation and the option "suspend on DBUS7 low" selected in MPROG. Also this configuration uses the pin BCBUS7, so this assumes that MPSSE mode is not selected. Copyright (c) 2009 Future Technology Devices International Limited 48 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 6.3 Oscillator Configuration FT2232H 27pF 2 OSCI 12MHz Crystal 27pF 3 OSCO Figure 6.5 Recommended FT2232H Crystal Oscillator Configuration. Figure 6.5 illustrates how to connect the FT2232H with a 12MHz 0.5% crystal. In this case loading capacitors should to be added between OSCI, OSCO and GND as shown. A value of 27pF is shown as the capacitor in the example - this will be good for many crystals but it is recommended to select the loading capacitor value based on the manufacturer's recommendations wherever possible. It is recommended to use a parallel cut type crystal. It is also possible to use a 12 MHz Oscillator with the FT2232H. In this case the output of the oscillator would drive OSCI, and OSCO should be left unconnected. The oscillator must have a CMOS output drive capability. Parameter Description Minimum Typical Maximum Units Conditions OSCI Vin FIn Ji Input Voltage Input Frequency Cycle to cycle jitter 2.97 3.30 12 < 150 3.63 V MHz pS +/- 30ppm Table 6.1 OSCI Input characteristics Copyright (c) 2009 Future Technology Devices International Limited 49 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 7 EEPROM Configuration If an external EEPROM is fitted (93LC46/56/66) it can be programmed over USB using MPROG V3.4a or later. The EEPROM must be 16 bits wide and capable or working at a VCC supply of +3.0 to +3.6 volts. Copyright (c) 2009 Future Technology Devices International Limited 50 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 8 Package Parameters The FT2232H is available in two different packages. The FT2232HL is the LQFP-64 option and the FT2232HQ is the QFN-64 package option. The solder reflow profile for both packages is described in Section 8.3 Copyright (c) 2009 Future Technology Devices International Limited 51 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 8.1 FT2232HQ, QFN-64 Package Dimensions Notes 1. All dimensions are in mm. 2. Pin 1 ID can be combination of DOT AND/OR Chamfer. 3. Pin 1 ID is NOT connected to the internal ground of the device. It is internally connected to the bottom side central solder pad, which is 4.35 x 4.35mm. 4. Pin 1 ID can be connected to system ground, but it is not recommended using this as a ground point for the device. 5. Optional Chamfer on corner leads. Figure 8.1 64 pin QFN Package Details Copyright (c) 2009 Future Technology Devices International Limited 52 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 8.2 FT2232HL, LQFP-64 Package Dimensions Top View 64 1 49 48 FTDI 10.000+/- 0.1 33 17 10.000+/- 0.1 D D1 64 49 E1 E Line 1- FTDI Logo Line 2- Date Code and Revision Line 3- Wafer Lot Number Line 4- FTDI Part Number Indicates Pin #1 (Laser Marked) YYWW-A XXXXXXXXXXXX FT2232HL 16 32 Dimensions are body dimensions (mm) 1 48 16 33 17 e 32 1.0 12 o +/- 1 o b c 0.25 1 . 4 + /- 0 . 0 5 MAX 1.60 c1 b1 0.05 Min 0.15 Max 0.2 Min 0.6 +/- 0.15 Figure 8.2 64 pin LQFP Package Details Copyright (c) 2009 Future Technology Devices International Limited 53 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 SYMBOL D D1 E E1 b c b1 c1 e MIN 11.8 9.9 11.8 9.9 0.17 0.09 0.17 0.09 0.5 BSC 0.2 NOM 12 10 12 10 0.22 MAX 12.2 10.1 12.2 10.1 0.27 0.2 0.23 0.16 Table 8.1 64 pin LQFP Package Details - dimensions (in mm) Copyright (c) 2009 Future Technology Devices International Limited 54 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 8.3 Solder Reflow Profile Figure 8.3 64 pin LQFP and QFN Reflow Solder Profile Copyright (c) 2009 Future Technology Devices International Limited 55 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 Pb Free Solder Process Profile Feature (green material) Average Ramp Up Rate (Ts to Tp) 3C / second Max. SnPb Eutectic and Pb free (non green material) Solder Process 3C / Second Max. Preheat - Temperature Min (Ts Min.) - Temperature Max (Ts Max.) - Time (ts Min to ts Max) 150C 200C 60 to 120 seconds 100C 150C 60 to 120 seconds Time Maintained Above Critical Temperature TL: - Temperature (TL) - Time (tL) Peak Temperature (Tp) Time within 5C of actual Peak Temperature (tp) Ramp Down Rate Time for T= 25C to Peak Temperature, Tp 217C 60 to 150 seconds 183C 60 to 150 seconds 260C see Table 8.3 30 to 40 seconds 20 to 40 seconds 6C / second Max. 8 minutes Max. 6C / second Max. 6 minutes Max. Table 8.2 Reflow Profile Parameter Values SnPb Eutectic and Pb free (non green material) Package Thickness Volume mm3 < 350 235 +5/-0 deg C 220 +5/-0 deg C Volume mm3 >=350 220 +5/-0 deg C 220 +5/-0 deg C < 2.5 mm 2.5 mm Pb Free (green material) = 260 +5/-0 deg C Table 8.3 Package Reflow Peak Temperature Copyright (c) 2009 Future Technology Devices International Limited 56 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 9 Contact Information Head Office - Glasgow, UK Future Technology Devices International Limited Unit 1, 2 Seaward Place, Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 E-mail (Sales) sales1@ftdichip.com E-mail (Support) support1@ftdichip.com E-mail (General Enquiries) admin1@ftdichip.com Web Site URL http://www.ftdichip.com Web Shop URL http://www.ftdichip.com Branch Office - Taipei, Taiwan Future Technology Devices International Limited (Taiwan) 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan , R.O.C. Tel: +886 (0) 2 8797 1330 Fax: +886 (0) 2 8751 9737 E-mail (Sales) tw.sales1@ftdichip.com tw.support1@ftdichip.com E-mail (Support) E-mail (General Enquiries) tw.admin1@ftdichip.com Web Site URL http://www.ftdichip.com Branch Office - Hillsboro, Oregon, USA Future Technology Devices International Limited (USA) 7235 NW Evergreen Parkway, Suite 600 Hillsboro, OR 97123-5803 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-Mail (Sales) E-Mail (Support) Web Site URL us.sales@ftdichip.com us.admin@ftdichip.com http://www.ftdichip.com Branch Office - Shanghai, China Future Technology Devices International Limited (China) Room 408, 317 Xianxia Road, ChangNing District, ShangHai, China Tel: +86 (21) 62351596 Fax: +86(21) 62351595 E-Mail (Sales): cn.sales@ftdichip.com E-Mail (Support): cn.support@ftdichip.com E-Mail (General Enquiries): cn.admin1@ftdichip.com Web Site URL: http://www.ftdichip.com Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. Copyright (c) 2009 Future Technology Devices International Limited 57 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 Appendix A - List of Figures and Tables List of Tables Table 3.1 Power and Ground .......................................................................................................... 9 Table 3.2 Common Function pins .................................................................................................. 10 Table 3.3 EEPROM Interface Group ............................................................................................... 10 Table 3.4 Channel A and Channel B RS232 Configured Pin Descriptions ............................................. 11 Table 3.5 Channel A FT245 Style Synchronous FIFO Configured Pin Descriptions ................................ 12 Table 3.6 Channel A and Channel B FT245 Style Asynchronous FIFO Configured Pin Descriptions.......... 13 Table 3.7 Channel A and Channel B Synchronous or Asynchronous Bit-Bang Configured Pin Descriptions ............................................................................................................................. 14 Table 3.8 Channel A and Channel B MPSSE Configured Pin Descriptions .................................. 15 Table 3.9 Channel B Fast Serial Interface Configured Pin Descriptions .................................... 16 Table 3.10 Channel A and Channel B CPU-style FIFO Interface Configured Pin Descriptions ... 17 Table 3.11 Channel A and Channel B Host Bus Emulation Interface Configured Pin Descriptions ................................................................................................................................................ 18 Table 4.1 FT245 Synchronous FIFO Interface Signal Timings ............................................................ 24 Table 4.2 Asynchronous FIFO Timings (based on standard drive level outputs) ...................... 27 Table 4.3 MPSSE Signal Timings ................................................................................................... 28 Table 4.4 MCU Host Bus Emulation Mode Signal Timings - write cycle ............................................... 30 Table 4.5 MCU Host Bus Emulation Mode Signal Timings- read cycle ................................................. 31 Table 4.6 Fast Opto-Isolated Serial Interface Signal Timings ............................................................ 32 Table 4.7 CPU-Style FIFO Interface Operation Select .............................................................. 35 Table 4.8 CPU-Style FIFO Interface Operation Read Status Description .................................. 35 Table 4.9 CPU-Style FIFO Interface Operation Signal Timing. .................................................. 36 Table 4.10 Synchronous Bit-Bang Mode Timing Interface Example Timings ........................................ 38 Table 4.11 Configuration Using EEPROM and Application Software ......................................... 40 Table 5.1 Absolute Maximum Ratings ............................................................................................ 41 Table 5.2 Operating Voltage and Current (except PHY) .................................................................... 42 Table 5.3 I/O Pin Characteristics VCCIO = +3.3V (except USB PHY pins) ........................................... 43 Table 5.4 PHY Operating Voltage and Current ................................................................................. 44 Table 5.5 PHY I/O Pin Characteristics ............................................................................................ 44 Table 6.1 OSCI Input characteristics ............................................................................................. 49 Table 8.1 64 pin LQFP Package Details - dimensions (in mm)........................................................... 54 Table 8.2 Reflow Profile Parameter Values ..................................................................................... 56 Table 8.3 Package Reflow Peak Temperature .................................................................................. 56 List of Figures Figure 2.1 FT2232H Block Diagram ................................................................................................. 4 Figure 3.1 FT2232H Schematic Symbol ...................................................................................... 7 Figure 4.1 RS232 Configuration .................................................................................................... 21 Figure 4.2 Dual RS422 Configuration ............................................................................................. 22 Figure 4.3 Dual RS485 Configuration ............................................................................................. 23 Figure 4.4 FT245 Synchronous FIFO Interface Signal Waveforms ...................................................... 24 Copyright (c) 2009 Future Technology Devices International Limited 58 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 Figure 4.5 FT245 asynchronous FIFO Interface READ Signal Waveforms ............................................ 26 Figure 4.6 FT245 asynchronous FIFO Interface WRITE Signal Waveforms .......................................... 26 Figure 4.7 MPSSE Signal Waveforms ............................................................................................. 28 Figure 4.8 MCU Host Bus Emulation Mode Signal Waveforms - write cycle.............................. 30 Figure 4.9 MCU Host Bus Emulation Mode Signal Waveforms - read cycle ............................... 31 Figure 4.10 MCU Host Emulation Example using a CANBus Controller ................................................ 31 Figure 4.11 Fast Opto-Isolated Serial Interface Signal Waveforms .................................................... 32 Figure 4.12 Fast Opto-Isolated Serial Interface Output Data ............................................................ 33 Figure 4.13 Fast Opto-Isolated Serial Interface Input Data............................................................... 33 Figure 4.14 Fast Opto-Isolated Serial Interface Example .................................................................. 34 Figure 4.15 CPU-Style FIFO Interface Operation Signal Waveforms. ....................................... 35 Figure 4.16 CPU-Style FIFO Interface Example ............................................................................... 36 Figure 4.17 Synchronous Bit-Bang Mode Timing Interface Example ................................................... 38 Figure 4.18 Bit-bang Mode Dataflow Illustration Diagram................................................................. 38 Figure 4.19 Dual LED UART Configuration ...................................................................................... 39 Figure 4.20 Single LED UART Configuration .................................................................................... 39 Figure 6.1 Bus Powered Configuration Example 1............................................................................ 45 Figure 6.2 Bus Powered Configuration Example 2............................................................................ 46 Figure 6.3 Self Powered Configuration Example 1 ........................................................................... 47 Figure 6.4 Self Powered Configuration Example 2 ........................................................................... 48 Figure 6.5 Recommended FT2232H Crystal Oscillator Configuration. ................................................. 49 Figure 8.1 64 pin QFN Package Details .......................................................................................... 52 Figure 8.2 64 pin LQFP Package Details ......................................................................................... 53 Figure 8.3 64 pin LQFP and QFN Reflow Solder Profile ..................................................................... 55 Copyright (c) 2009 Future Technology Devices International Limited 59 Document No.: FT_000061 FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI#77 Appendix B - Revision History Revision History Version draft Version Preliminary Version 1.00 Version 1.10 Version 2.00 Version 2.01 Initial Datasheet Created Preliminary Datasheet Released Datasheet Released QFN Package updated Various Updates Corrections made to table 3.6, 3.7, table on page 8. Changed description of WRSTRB# and RDSTRB# Added note that HBE mode only operates at 60MHz Version 2.02 Corrections made to tray QFN 160 changed to 260 Correction made to 3.4.2, falling changed to rising Version 2.03 Corrections made to TxLED and RxLED pin connections Corrected signals in Figure 4.16. Corrected signal names in Fig 2.1 Added reference to AN_108, AN_109, AN_110, AN_111 and AN_113. Version 2.04 Version 2.05 Added paragraph on latency timer to section 4.1 Corrected Figures 6.2, 6.3 an 6.4 - missing regulators and better way of holding self powered designs in reset if not connected to USB. Corrected Max DC inputs on "DC Input Voltage - "All Other Inputs" pins from VCORE+0.5V to VCCIO+0.5V 3rd June 2009 17th June 2009 19th May 2009 March 2009 October 2008 23rd October 2008 4th November 2008 November 2008 January 2009 February 2009 Copyright (c) 2009 Future Technology Devices International Limited 60 |
Price & Availability of FT2232H
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |